I try to create bare metal application for TI am335x soc based board. One thing I need to do is to invoke callback1 on rising edge and callback2 on falling edge. From the datasheet I figured out, that simultaneous detection for rising and falling edge could be enabled by writing 1 << pin to RISINGDETECT and FALLINGDETECT GPIO registers. However, I can't understand (see no signs of it in datasheet), how could I determine if the currently appeared interrupt was caused by RISING edge on GPIO or by FALLING edge?
GPIO irq: Falling and Rising edge detection
2.3k views Asked by Alex Hoppus At
1
There are 1 answers
Related Questions in ARM
- Jiobook flashing
- How to flush denormal numbers to zero for apple silicon?
- How to exploit Unified Memory in OpenCL with CL_MEM_ALLOC_HOST_PTR flag?
- ARM Assembly code is not executing in Vitis IDE
- Which version of ARM does the M1 chip run on?
- Vector by Scalar Division with -ffast-math
- Why veneer code generated by gcc for cortex-m0 seems 8-byte aligned?
- Getting almost random time stamp counter on ARM
- Portenta H7 Baremetal Development and a Little Guidance on Embedded System Learning Roadmap
- STM32 RTC3 Mixed Mode: Writing TR resets SSR
- Implementing Quick Sort Algorithm in Visual2 with armv7
- How can I create an Inline assembly command with a multi-variable register offset?
- Inquiry: ARM Compatibility for Puppeteer
- Confusion with thumb instructions while compiling recipe for cortexm4 CPU
- Difficulty understanding virtual LPIs in GICv3
Related Questions in EMBEDDED
- MSP430F5529 on the MSPEXP430F5529LP: UART is not actually transmitting despite seemingly correct setup. What is wrong?
- A FPGA Project Proposal where I can use both PS and PL
- Program doesn't run after DFU
- Sending struct through queue
- How to generate a VPI warpmap for polynomial distortion correction?
- How to present this example concept in UML: Using 2 LCD displays in C/C++
- CLion: Debug via St-Link
- Portenta H7 Baremetal Development and a Little Guidance on Embedded System Learning Roadmap
- STM32 RTC3 Mixed Mode: Writing TR resets SSR
- Unable to read value from gpio set as input
- Mbed TLS: in-place en-/decryption for OAEP doesn't seem to work
- Shared variable read from low priority thread in preemptive scheduling
- Own Pattern / framework for interfacing with components in C
- Performance Difference Between Global Variable and Local Variable in Embedded Systems
- Comparing analog signal from Electret mic with samples
Related Questions in GPIO
- Accessing GPIO via MMIO in Android App on Raspberry Pi 4
- Unable to read value from gpio set as input
- Turning on an LED using Assembly on raspbianOS (Raspberry Pi 3 Model B)
- Driving Fintek F75113 GPIO
- IRQ interrupt obtaining abnormal possibilities
- Error compiling dts (Device Tree source) file for dtb
- asyncio only running first gpiozero coroutine
- Rf module getting signals when i use ssh, but not when i send it from the transmitter
- VLC - python and GPIO - random fonction
- Use raspberry pi 4 GPIO with node js
- How to add a button handler to GPIO pin through a push button
- Can't access GPIO on Python from Docker container on Raspberry Pi 5
- Are FPGA GPIOs capable enough to read bits at a high rate (26Mbps)? If not, what is a possible way?
- Terminal errors when running my project code, which uses GPIO
- How to set up GPIO event listeners on a Raspberry Pi using Rust
Related Questions in IRQ
- STM32MP1 linux IRQs & EXTI controller config in DTS file
- How to trigger the Linux IRQ handler thread again when it finishes if there was same IRQ triggered while it was running
- /proc/interrupts not showing all irqs
- convert HW IRQ to Linux IRQ
- How to provide interrupt generating GPIOs from a kernel module
- Why are all irq disabled for retarget write on STM32?
- how to use interrupt function in Ubuntu 20?
- Can I increase a thread irq priority
- do I need to fill all the IDT exception entries, before handling IRQs?
- About the use of tasklet_hrtimer_init in hardware interrupt callback function
- How to know whether an IRQ was served immediately on ARM Cortex M0+ (or any other MCU)
- Crash when adding or removing data in code on an IRQ
- RPi Pico freezes on IRQ Interrupt call
- Linux kernel IRQ to execute long action
- GICv2 IRQ ID 1023
Related Questions in OMAP
- Linux kernel issue when booting from U-Boot on Cortex-A15 CPU QEMU
- Finding physical adresses of registers in memoryspace
- Select Wayland output for QT application
- How to recover a embedded CE mobile device bricked after OS update
- Can't read SDRAM of TI OMAP5912 ARM core using JTAG
- AM335x - i2c slave for linux kernel
- How to fix 'warning #1173-D: attribute "deprecated" ignored?'
- Why is code relocation done in U-boot proper?
- Kernel panic on linux-omap 4.3.0-rc5 on IGEPv2 board
- GPIO irq: Falling and Rising edge detection
- Stop MMC queue from fetching new requests when communication with card times out
- Why is UART TX interrupt not forwarded to GIC on OMAP4430
- fw_printenv fw_setenv on var-som-am33 is failing
- Additional static array breaks the DSP application on omapl138 target (ccs5.2)
- OpenGL ES 2.0 on SGX540 OpenGL Offscreen PIXMAP Support
Popular Questions
- How do I undo the most recent local commits in Git?
- How can I remove a specific item from an array in JavaScript?
- How do I delete a Git branch locally and remotely?
- Find all files containing a specific text (string) on Linux?
- How do I revert a Git repository to a previous commit?
- How do I create an HTML button that acts like a link?
- How do I check out a remote Git branch?
- How do I force "git pull" to overwrite local files?
- How do I list all files of a directory?
- How to check whether a string contains a substring in JavaScript?
- How do I redirect to another webpage?
- How can I iterate over rows in a Pandas DataFrame?
- How do I convert a String to an int in Java?
- Does Python have a string 'contains' substring method?
- How do I check if a string contains a specific word?
Popular Tags
Trending Questions
- UIImageView Frame Doesn't Reflect Constraints
- Is it possible to use adb commands to click on a view by finding its ID?
- How to create a new web character symbol recognizable by html/javascript?
- Why isn't my CSS3 animation smooth in Google Chrome (but very smooth on other browsers)?
- Heap Gives Page Fault
- Connect ffmpeg to Visual Studio 2008
- Both Object- and ValueAnimator jumps when Duration is set above API LvL 24
- How to avoid default initialization of objects in std::vector?
- second argument of the command line arguments in a format other than char** argv or char* argv[]
- How to improve efficiency of algorithm which generates next lexicographic permutation?
- Navigating to the another actvity app getting crash in android
- How to read the particular message format in android and store in sqlite database?
- Resetting inventory status after order is cancelled
- Efficiently compute powers of X in SSE/AVX
- Insert into an external database using ajax and php : POST 500 (Internal Server Error)
Try checking the state of the pin.
A rising edge results in a
onstate, whereas a falling edge results in aoffstate.So the current state of the pin implies the direction of the most-recent interrupt.